What brand of oil to pour into the Renault Sandero engine

How to properly replace the filter

When changing the oil filter for 1.6 liter Renault Sandero Stepway crossovers, the work is performed according to the following algorithm:

1. The power unit must be warmed up. Thanks to this, the operating temperature corresponds to a certain level, which has a positive effect on the fluidity of the oil. The filler cap is unscrewed from above to equalize the pressure.
2. In order to have access to the crankcase, the car must be jacked up, having first been driven onto an overpass or inspection pit.
3. The area around the drain hole is cleaned. To drain under it, use a container with a volume of 4 liters or more.
4. The drain plug is carefully unscrewed with the tenth key. The rubber seal is inspected from the reverse side for integrity. In case of defects, it is replaced with a new one.
5. After the waste is completely drained, the oil filter is removed either by hand or with a special puller. If there is interference from the insulating screen, it is dismantled.
6. A new puller is placed after the threads have been thoroughly cleaned. It is filled with engine oil to half its capacity.
7. Tighten until the rubber seal comes into contact with the power unit housing. Then it is further rotated through an angle of up to 2700.
8. Then oil is poured into the engine part in the volume set by the manufacturer for a specific engine model.
9. The pipe plug is tightened. A test run is being carried out. After the engine starts running, the oil pressure indicator goes out. An external inspection determines the presence of leaks. After plugging the power unit, check the oil level in the engine with a dipstick.

Changing the engine oil in Renault Sandero Stepway

To change the engine oil, you will need fresh engine oil, as well as other consumables, for example, an oil filter - MANN-FILTER W 75/3. All the necessary tools should be at hand: wrenches, sockets, oil filter puller. The engine first warms up, after which the old oil is drained and the filter is changed. Fresh technical fluid is poured in, the oil level is checked, after which the engine is allowed to run and the oil level is checked again.

You can see the detailed oil change process in the video:

Changing the oil in a Renault Sandero Stepway gasoline engine:

Lubricant selection

Car owners are faced with a logical question about what kind of oil to pour into their Renault Sandero car. Here the plant recommends following their advice without creating unnecessary problems for yourself. And this is so, since almost identical Elf oils are recommended for all Renault cars. This is the optimal composition for a French car of any model. Therefore, with it you will know for sure that the car will behave well and not create unnecessary problems. The recommended oil must match the conditions in which you intend to operate the machine. Therefore, it is better to fill the following brands of motor lubricants into the Renault Sandero or Renault Sandero Stepway engine:

• Excellium LDX;
• Evolution SXR;
• Solaris RNX;
• Competition ST;
• Turbo Diesel.

Now let’s talk about what kind of oil viscosity would be best to fill in Renault Sandero. Here everything depends on climatic conditions. For some, all-season oils are not suitable, so the driver uses different lubricants for winter and summer. Here you have to carry out the change procedure twice a year. If the winter is not overly harsh, then in most cases car owners opt for all-season lubricants.

For Renault Sandero recommends the following viscosity values:

• 0W;
• 5W;
• 0W40;
• 5W30;
• 5W40;
• 10W40.

Such lubricants will not negatively affect fuel consumption and will be able to provide optimal lubricating and cooling properties for the engine. But each car owner himself chooses which oil to pour into Renault Sandero. It is better not to deviate from the factory recommendations. Reviews clearly show that Renault Sandero behaves excellently with Elf oils, but problems often arise when using alternative lubricants, especially cheaper ones.

Required quantity

The volume of oil to be filled depends on what engine is installed in your Renault Sandero. Therefore, build on this characteristic. In the case of 16-valve 1.6-liter engines (K4M and K7M), you will need a 5-liter canister, since the engine provides about 4.8 liters. lubricant. Eight-valve 1.4-liter engines require less fluid. They contain about 3.5 liters. lubricants All engines designed for Renault Sandero allow the use of the same oils. The only difference is how much oil to pour into the engine and under what conditions the car will be operated. Here you should proceed from the specific situation. For Renault Sandero, it is recommended to always have some lubricant on hand. Although oil consumption is negligible under normal conditions, engine oil may need to be topped up as the engine operates. Over the course of a year, the liquid will definitely not lose its properties and characteristics, so it would be correct to initially purchase 1 liter more than you need before the planned replacement.

Oil viscosity

The viscosity of engine oil for Renault Sandero 1.6 depends on natural conditions. Some car owners are not satisfied with all-season engines, when drivers fill in different engine oil in winter and summer, and it must be drained twice a year. When winter is not very severe, Renault owners choose all-season.

A common mistake is skimping on liquids. Many people purchase compounds that do not have the necessary properties. With such engine oil, the unit is unpredictable and will not last until the next replacement. To maintain the performance of Renault Sandero engines, experts recommend following a cycle and a certain replacement frequency. Replacement dates should be recorded.

Timely maintenance is one of the main conditions for successful operation of a car. In order for the unit to function efficiently and not be subject to wear, the lubricant must be changed regularly. By using the recommended motor oil, the formation of carbon deposits on drive elements can be eliminated. You can do the replacement yourself, without having experience in car maintenance. You just need to familiarize yourself with the nuances of the process. If Renault is still under warranty, you should contact a service station.

Selection of motor oil

All motor oils existing today are divided into:

• mineral water;
• synthetics;
• semi-synthetic.

Renault recommends using ELF Evolution SRX 5W30/5W40 in cars. It is worth noting that some service centers pour lubricants into machines from other manufacturers. This does not affect the warranty in any way. However, if the car owner decides to fill the car with an oil fluid that differs from the recommended one, a special mark will appear in the service book.

Because of this mark, the manufacturer may refuse to repair the vehicle, even if the warranty period has not yet expired. Car engines wear out due to contact between parts. Oil for Renault provides the opportunity to reduce friction and slow down the wear of engine parts.

ELF Evolution SRX 5W30 is recommended for Renault by the automaker. It, according to the ACEA classification, is classified in category A1B1. This type of engine oil is energy saving

When purchasing, pay attention to what is written on the lubricant container. The inscription “Full Economy” indicates that the petroleum product is used in unboosted internal combustion engines without turbocharging

This lubricant is best poured into vehicles that require the use of consumables with a low viscosity index.

ELF Evolution SRX 5W40 belongs to ACEA A3B4. This petroleum product must be poured into Renaults equipped with forced gasoline engines. In addition, this consumable is optimal for internal combustion engines running on diesel and equipped with turbocharging.

What is the price of original engine oil for Renault? The minimum price for a canister is one and a half thousand rubles. ELF lubricants (not ELF Evolution) cost 500 rub./l. They are made in France.

Algorithm for replacement in a 1.6-liter Logan unit

1. Unscrew the plug on the neck to fill the lubricant.
2. Under the crankcase of the Renault Logan engine version 1.4 and, accordingly, 1.6, we substitute a container of suitable volume to collect the “working off”.
3. We remove the plastic crankcase protective plate (on “8-valve” engines you don’t have to dismantle the protection, since it has a technological cutout for the drain plug).
4. Unscrew the drain plug on the pan (with a square key set to “9”).
5. We wait until the lubricant is completely drained.
6. During this time, unscrew the housing of the old filter element (use a puller or other available means: a screwdriver, part of an emery sheet, etc.).
7. Before installing a new element on Renault Logan, lubricate its rubber ring with “fresh” oil.
8. We install the filter by screwing its housing onto the mounting threaded channel in the motor using hand force.
9. Don't forget to install the sealing washer on the drain plug (consumable code - 1026 5505R).
10. Fill in new lubricant.
11. The liquid level position should be slightly below the mark marked on the dipstick.
12. We tighten the filler plug on the valve cover.
13. We start the engine and let it run for 5-6 minutes.
14. We turn it off and wait 15-20 minutes.
15. We control the level - it should be between o - “MAX”.
16. We inspect the locations of the filter housing and drain plug and make sure there are no leaks.
17. In order to correctly control the quality of lubricant in the Renault Logan engine, you should note the mileage at which this process was performed.

Now you have made a conclusion for yourself which oil to pour into the car engine. Before filling, it is recommended to flush the system with lubricant from the same manufacturer. To do this, pour about 1 liter of oil into the crankcase, start the engine and let it run for several minutes. We turn off the engine and start draining the lubricant. Washing is performed with the old filter element, along with which contaminant particles will be removed when replaced.

Preliminary work before replacement

Before changing antifreeze on Sandero, you should prepare a box with tools and additional devices in advance. The list is as follows: small rags, pliers, a container designed to hold at least 10 liters and new coolant.

Before you start draining the fluid, you should allow the Renault Sandero engine to cool thoroughly. Personal protective equipment must be used. In this case, the following are suitable: a respirator, gloves, and safety glasses to prevent coolant from getting into your eyes. The machine is fixed on a horizontal, flat surface. Before starting the replacement procedure, you should monitor the system for leaks, especially pay attention to the connecting nodes in the thermostat at the hose supply points. If the tightening is weak, install new clamps.

The filler cap of the expansion tank is unscrewed. If protection is installed on the engine crankcase, it must be removed. Using pliers, loosen the clamp that holds the hose at the bottom of the car's radiator. The clamp is pulled along the hose. Then the rubber tube is disconnected from the radiator and the antifreeze is drained into the bath, which was previously placed under the pipe. We are waiting until there is no antifreeze left in the system. Then the valve plug designed to release air is unscrewed. A certain amount of substance is poured through the neck of the tank to flush the system. Then, by pumping up pressure using a compressor unit, complete purging is performed.

The hose that fits from below to the radiator is installed in its original place and firmly fixed using a clamp. New coolant is poured into the expansion tank when the valve cap responsible for releasing air is removed. The update occurs until antifreeze begins to appear from the valve instead of air. This is a signal that the reservoir cap and cap should be tightened. The next stage involves starting the Renault Sandero engine to give it the opportunity to drive antifreeze through the system. Antifreeze is replaced independently, without causing any difficulties for the car owner.

What kind of oil should I put in the engine?

”alt=””>

As you know, there are three types of motor oil:

• Mineral oil is an oil that is very unstable and capricious in its behavior; it is highly not recommended to use such a product at subzero temperatures, as it thickens, and detergents and anti-corrosion additives that are poured in tandem with oil simply burn out when exposed to high temperatures. Such oil is cheaper than its synthetic analogues, since when this product is obtained from oil, its molecular composition is not changed in any way.
• Semi-synthetic oil is recommended for replacement in engines with a mileage of more than 100,000 kilometers. Because it is thicker than synthetic, the possibility of leakage through dried gaskets and seals is reduced. Such a lubricant is somewhere between “mineral water” and “synthetic” in terms of performance and the golden mean in terms of price and quality. At low temperatures, it provides the easiest starting.
• Synthetic is the type of oil recommended for use on all modern engines. It has the greatest fluidity and a high level of stability in its characteristics. This type of oil is least afraid of overheating and frost.

Note!

One thing to remember is that the oil change for Renault Logan should be done with one that has already been filled or another with similar characteristics and properties. Incorrectly selected oil can leave carbon deposits inside the engine, which will lead to timing belt breakage and major repairs. The cost of repairs for 16-valve engines will be more expensive than for 8-valve engines, take this into account when choosing a car.

In other cases, if nothing is known about the origin of the old oil, the engine should be flushed with special detergents. By following these simple rules and recommendations, the motor will last a long time.

About Renault Sandero

It is a compact B class hatchback. Renault Logan was used as a platform. On the market since 2007, 3 years after its foundation. It received a shortened wheelbase and a radically different appearance, inheriting the Renault Scenic. The model positions itself as a youth model. Affordable price and good equipment helped to gain love and demand in the market. Since 2010, it has been manufactured in Russia, at the company’s factory located in Moscow. As standard, the heart was a 1.4 liter 8-valve petrol engine with a power of 75 hp. With. There are modifications with a volume of 1.6 liters, receiving 8 and 16 valve engines, receiving 84 and 102 liters. With. respectively.

Since 2014, the second generation Renault Sandero has been launched into production, based on the 2012 Logan. Its heart is a 1.6-liter engine with a power of 82 hp. With. (basic), 100 l. With. (deformed) and 113 l. With. (top-end configuration).

Both generations are available with manual and automatic transmissions.

How to choose the right oil?

What oil is best to fill? The Renault brand recommends using “ELF Evolution SXR” lubricant with “5W40” or “5W30” ratings for Renault Logan model engines. As an alternative, it is possible to use a synthetic substance that meets the regulatory temperature criterion:

• "5W40";
• "5W30";
• sometimes - “0W30 AM”.

When replacing the lubricant, it is necessary to change the o-ring on the drain plug and the filter element.

The specifications for these consumables are as follows:

• at the sealing ring for the plug - 11026 5505R.
• for the oil filter element - 7700274177 or 8200768913 (both options are identical).

How much to fill in Stepway

An important issue remains the amount of lubricant required to replace it in the Renault Sandero engine compartment. The type of engine plays a role here and you need to know the volume of oil in the engine.

For engines with 8 valves and a volume of 1.6 liters, the optimal level will be 3.5 liters. For engines with 16 valves - 5 liters of fluid.

You should have a certain supply of lubricant, since it will not disappear anywhere. But if there is a shortage of Renault Sandero with a volume of 1.6 liters, troubles may arise.

According to the regulations for replacing lubricants, in particular motor lubricant, Stepway should be replaced after driving the car for 15 thousand km, which corresponds to 1 year of normal operation. Service station specialists and the French automaker itself advise pouring oil for Renault Sandero into the engine with synthetic fluid Elf Evolution 5W30, 5W40, this is the answer to the question what kind of oil to fill? On the crossover, barriers are replaced to clean the air and lubricate the engine. It is possible to use other filter elements for the machine. However, they must be included in the list of components recommended by Renault. In order to find out the brands of oils that will be compatible with your car, you should watch the video.

How to check volume

To check the volume of liquid, you need to check its level. Especially for this purpose, there is a dipstick located in the oil filler hole in the engine compartment of the car. We take out the dipstick and look at the oil print. If the liquid is clear, but its level is below the Min mark, then you only need to pour in a certain amount of oil. It is necessary to enter until the level until the consumable reaches the average value, that is, between the Max and Min marks on the dipstick. The situation can become more complicated if the oil is dark brown, indicating mechanical wear on the internal parts. In this case, you first need to pour out the old oil and then introduce new fluid.

When to change

Changing the oil does not require much time and effort. But for some reason, many motorists constantly postpone this procedure, believing that the car will last several hundred kilometers without any problems on the old lubricant. In practice, this approach often leads to dire consequences. Over time, even without severe operating conditions, the oil becomes unusable. The liquid loses its original characteristics, physical and chemical properties, which is why it simply cannot cope with the tasks assigned to it. And we are talking about lubrication and cooling of engine parts, without which the engine will first work worse, and then may completely fail.

To prevent your Renault Sandero from encountering something like this, you need to change the oil on time. And here it would be natural to ask how often this should be done and in what time frame. To answer, you need to first look at the Renault Sandero owner's manual. The French automaker indicates in the manual that on Renault Sandero, regardless of the type of engine installed, the oil is changed at intervals of 15 thousand kilometers. This is for gasoline engines. In the case of diesel units, the plant recommends changing the lubricant every 10 thousand kilometers. But car owners themselves do not agree with this interval, calling it too large for real operating conditions.

The following factors influence the reduction of the recommended interval between lubricant changes:

• bad roads;
• long machine downtime;
• driving in traffic jams;
• low fuel quality;
• aggressive driving style;
• very hot summers or extremely cold winters;
• sudden temperature changes, etc.

Under the influence of such negative processes, the oil begins to quickly lose its properties. Therefore, it has to be changed more often. With relatively moderate severity of operating conditions, it is recommended to reduce the interval to 10 - 12 thousand kilometers. If the car has to be used in difficult conditions, then it is better to change the lubricant after 6 - 8 thousand kilometers. This is true for heavily worn cars with high mileage. But regardless of the number of kilometers traveled, it is not recommended to change the oil less than once a year. Therefore, focus on what comes first.

Oil level and condition

Every car owner is required to regularly monitor the oil level in their Renault Sandero or Renault Sandero Stepway. Although the cars are different in appearance, they have the same essence. Experts and simply experienced motorists advise checking the level every 1 thousand kilometers or before long trips. This will avoid unpleasant surprises on the road. There should be no problems checking the amount of lubricating fluid. Diesel and gasoline versions of engines are equipped with oil dipsticks located in the engine compartment.

You need to do the following:

• warm up the car to operating temperature (this way you will find out the real level);
• let the car cool down a little and the oil drain into the crankcase;
• pull out the dipstick;
• wipe it with a lint-free cloth;
• insert the oil dipstick back;
• wait a few seconds;
• pull it out again.

Now look at the level. It is determined by the trace of oil on the dipstick. Renault Sandero and Stepway have two marks, which indicate the minimum (Min) and maximum (Max) level. Always make sure that the dipstick does not show a mark below the minimum, since operating a car with such an amount of lubricant is very dangerous. But you also cannot exceed the maximum mark. Try to keep the level closer to Max or in the middle. Between these two marks there is about 1.5 - 2 liters of lubricant. This already depends on the specific engine. In parallel with checking the level, you can evaluate the current state of the liquid. To do this, simply drop a few drops of lubricant onto a paper napkin. If you see that the oil is black, has some impurities, or has an odor uncharacteristic of motor fluid, its service life has come to an end and requires replacement. There is nothing to worry about if the oil has slightly changed its characteristics by the time of the scheduled replacement. It’s much worse if such signs appear 2–3 thousand kilometers after the shift. This indicates problems with the engine, which must be eliminated in the near future.

Changing gearbox oil for RENAULT SANDERO

Oil for (5/1 manual transmission) 5-speed manual transmission

. Filling volume from 2.5 l. up to 2.8 l. to the level of the filler neck. Replacement interval according to the operating manual.

The viscosity class of the native 75W-80 API GL-4, in the absence of such a viscosity class, you can consider the products 75W-85 API GL-4 and 75W-90 API GL-4. All these products are synthetic, which allows them to be used all year round. From -47 C to + 60 C.

The following products are also high-quality analogues:

Taking into account operating conditions, it is recommended to check the car every 20 thousand km.

General recommendations for replacement are simple. When the volume is indicated (example from 1l - 1.2l), it is necessary to measure the amount of drained, used oil and fill in the same amount of new oil (if there were no oil leaks). This diagram is applicable if there is no dipstick in the gearbox or a mark at which level to fill.

Usually all this information is well documented in the vehicle maintenance book. But there are exceptions to the rules; not all manufacturers indicate the filling volume in the service book.

Changing the gearbox oil in RENAULT SANDERO / SANDERO STEPWAY yourself Video

Video “Step-by-step instructions for changing the oil in a manual transmission in a RENAULT SANDERO”