Stages of replacing lubricant VAZ 2105
On classic Lada cars or the more familiar Zhiguli, a convenient drainage of used oil from the engine is provided. The oil filter is also easily accessible and can be reached from the engine compartment.
During the production of the VAZ 2105, a large number of modifications were produced, which were equipped with various engines. Experienced drivers note good maintainability, unpretentiousness in maintenance, as well as consumables.
Before starting to replace the lubricant, precautions should be taken. It should be noted that the drained waste will be at a high temperature. Since the replacement is carried out on a warm engine.
Necessary tool
To change the engine oil, you need to prepare the following tools and accessories:
- hex key 12;
- star key 14 x 17;
- special wrench for unscrewing the oil filter;
- tube Ø 12 mm;
- 5 liter container for draining used oil;
- purchase 4 liters of appropriate oil;
- new oil filter.
Changing the oil in the VAZ 2105 engine. Keys and accessories
We make a replacement
Before draining the used oil, start the engine and warm it up to operating temperature, that is, up to 90ºC. So:
- Then we drive the car onto a pit or overpass to make it easier to work under it.
- We turn off the engine and wait 10 minutes. During this time, all the oil from the system will drain into the engine crankcase.
Changing engine oil on a VAZ 2105. Draining used oil
- Then we place a container for used oil under the drain plug on the crankcase. Use a hex wrench to unscrew the drain plug.
Attention: you must unscrew the plug carefully, as the oil is hot. To avoid scalding your hands, it is better to wear gloves.
- In order for the oil to drain faster, it is necessary to remove the filler plug on the valve box cover.
Open filler neck
- While the oil is draining, you can unscrew the oil filter. This can be done with gloved hands. If the filter cannot be unscrewed by hand, then in this case you need to use a special wrench, which can be purchased at any auto parts store.
- We take a new filter, fill it with about 250 grams of clean oil of the same brand that you are going to pour into the engine. Check the rubber gasket. If there are no visible defects on it, then lubricate it with oil and screw the filter into place by hand, trying not to strain too much. It is better to tighten it up after the oil has warmed up.
- If all the oil has drained, screw the drain plug into place, first checking the gasket for any defects.
Unscrew the oil filter
- Now you can add fresh oil.
VAZ 2105 engine oil change
This is done through the filler neck on the engine valve cover. For convenience and to avoid spilling the oil, you can adapt the cut off upper part of a five-liter plastic container into a funnel. So:
- When pouring oil into the engine, it is necessary to monitor its level using the dipstick. Before measuring, you need to give time for the oil to drain into the crankcase. The oil level on the dipstick should be 2/3 between the minimum and maximum marks.
Minimum and maximum marks on the dipstick
- After the oil has been changed in the VAZ 2105 engine, it is necessary to close the filler neck with the cap and start the engine.
After starting, you must carefully monitor the oil pressure warning lamp. If it does not go out within 3-4 seconds, you should immediately stop the engine. After a short stop, restart the engine. If the light does not go out within 3-4 seconds, then repeat stopping and starting the engine again.
Attention: Under no circumstances allow the engine to run for more than 4–5 seconds with the warning light not extinguished, and certainly do not sharply increase the speed. This could lead to a serious accident. If the light remains on, check the oil pressure sensor.
- After you have started the engine and the warning light has gone out, let the engine run and warm the oil to operating temperatures. Inspect the engine for oil leaks. If necessary, tighten the oil filter.
- Stop the engine and check the engine oil level 5 minutes after stopping. If the oil level shows below the middle between the marks, then add oil to the level of 2/3 of the distance between the min and max marks.
- The next VAZ 2105 engine oil change is performed after 10,000 km of your car.
Attention: To monitor the mileage of the car from replacement to oil change, record the speedometer readings and save the records. You will know exactly how many kilometers the car has traveled since changing the oil, and how much is left to travel before the next change.
This is important to know if you are planning a long trip, and so that this procedure does not catch you along the way. Changing the oil in the VAZ 2105I engine is done in exactly the same way as in the VAZ 2105 engine. Therefore, changing the oil can be done by following the instructions outlined above. A comprehensive oil change for a VAZ 2105 engine, including flushing the crankcase, manual lubrication of locks and hinges at a service station will cost you approximately 1,350 rubles.
Changing the oil and oil filter VAZ “classic”
So, let's look at the oil change procedure using the VAZ 2106 as an example. First of all, the volume of oil in the VAZ 2106 engine for replacement is 3.75 liters. You also need to purchase a new oil filter that will be completely suitable for this type of engine.
- First of all, before changing the lubricant, the engine must be warmed up to operating temperatures. This will maximize the fluidity of the oil, which liquefies with heat. End of form
- Then the car needs to be lifted on a lift and driven onto an overpass or inspection hole. The main task is to gain free access to the drain hole, which is made in the oil pan.
- Next (in the case of an inspection hole or overpass), the car is fixed using the handbrake and engaging first gear. You can also additionally install wheel chocks, etc.
- If there is an installed engine crankcase protection, it is recommended to remove such protection, even taking into account the fact that a special hole may be made in the protection itself for draining the oil. This will make the procedure easier if you lack practical skills in changing the oil.
Replacement frequency, what oil to fill
According to the manufacturer's regulations, service changes of engine oil on the VAZ 2105 are carried out after 8,000-10,000 kilometers or at intervals of 1 year. But some car owners consider this interval to be a little too high, recommending that it be shortened taking into account operating conditions.
It is recommended to use semi-synthetic with a viscosity of 10W-40 as a lubricant. The following motor oils are most popular among model owners:
- Lada Professional 10W-40
- Lukoil Genesis Advanced 10W-40
- Shell Helix HX7 10W-40
- Total Quartz 7000 10W-40
When using this car in winter, you should select oil taking into account the climate zone, as well as the recommendations of AvtoVAZ. Viscosity 5W-40 will allow you to operate the car down to -30°C, and 0W-40 up to -35°C.
How much oil is in the engine lubrication system, volume table
| Model | Engine capacity | Motor marking | How many liters of oil are in the system | Original oil / factory filled |
| VAZ 2105 | gasoline 1.6 | VAZ-21067 | 3.75 | Lada Professional 10W-40 |
| VAZ-2106 | ||||
| gasoline 1.5 | VAZ-2103 | |||
| gasoline 1.3 | VAZ-21011 | |||
| VAZ-2105 | ||||
| VAZ-4132 | ||||
| gasoline 1.2 | VAZ-2101 | |||
| diesel 1.5 | VAZ-341 | TNK Magnum Super 10W-40 |
What oil to use for the VAZ 2105 engine
Original
VAZ-2105 owners use mineral, semi-synthetic or synthetic motor oil with different viscosities. Semi-synthetics are considered the most popular for this model. Viscosity is selected depending on temperature conditions. For example, for year-round operation, a 10W-40, 10W-30 or 5W-40 all-season oil is recommended. In the winter season, it is better to fill in 0W-30, 0W-40 or 5W-30, and in the summer you can opt for 20W-40 or 25W-50.
Unoriginal
Owners of VAZ-2105 cars prefer inexpensive motor oils from domestic brands Lukoil, Rosneft, G-Energy and Gazpromneft. When choosing a suitable product, it is necessary to take into account the API approval, which is selected depending on the year of manufacture of the car, as well as the type of internal combustion engine. For example, for a gasoline VAZ-2105 produced in 1980. All-season mineral oil with parameters 15W-20 and API-SG is suitable. For cars of the 2010 model year, semi-synthetic API-SL is recommended. Below are the best options for analogue motor oils for the VAZ-2105.
- ZIC X5 10W-40
- Lukoil Lux 10W-40
- Mobil Super 3000 5W-40
- G-Energy 10W-40
- Eneos 10W-40.
What kind of oil should I use and how much?
Before changing the oil, make sure there is enough oil. You need to buy a 4 liter eggplant, because... 3.75 liters will go into the engine.
Below is a table that will help you choose the optimal viscosity and brand. When choosing a viscosity, pay attention to the climate in which you live. If one viscosity is suitable for hot regions, then for cold regions it is completely different. For residents of the middle zone, it is better to take a closer look at the universal viscosity 10W-40, 15W-40, etc.
Several suitable for 2105 filter (from a large selection today).
- M-005 (article for online search)
3$
WL7067-12
Changing the oil of VAZ 2105
VAZ 2105 is a rear-wheel drive car originally from the USSR and then Russia. Developed at the Volzhsky plant, it has a sedan-type body. Production started in 1979 and lasted until 2010. It was this model that was produced the longest of the entire Zhiguli line, for 31 years.
A variety of modifications of the model were produced:
- LADA-2105;
- LADA-21050;
- LADA-21051;
- LADA-21053;
- LADA-21053-20;
- LADA-21054;
- LADA-21054-30;
- LADA-21055;
- LADA-21057;
- LADA-21058;
- LADA-21059;
They all had some differences in terms of the engine. One version had a 1.2 liter engine and the other 1.45. For example 21058 was an export model with a right-hand drive (for the UK).
All versions of the car need to be serviced. The manufacturer's regulations indicate changing the engine oil every 15,000 km. In fact, the owners try to change the oil earlier, at about 10-12 thousand, explaining this by the quality of expensive products in our markets.
- What kind of oil should I use and how much?
- Instructions
- Video materials
What kind of oil should I use and how much?
Before changing the oil, make sure there is enough oil. You need to buy a 4 liter eggplant, because... 3.75 liters will go into the engine.
Below is a table that will help you choose the optimal viscosity and brand. When choosing a viscosity, pay attention to the climate in which you live. If one viscosity is suitable for hot regions, then for cold regions it is completely different. For residents of the middle zone, it is better to take a closer look at the universal viscosity 10W-40, 15W-40, etc.
| Year | Viscosity SAE all season from +25 to -25 °C | winter from -35 to 0 °C | summer from 0 to +35 °C |
| 20W-20 20W-30 20W-40 25W-20 |
| 5W-20 5W-30 10W-30 10W-40 | 20W-30 20W-20 20W-40 25W-30 25W-20 |
| 5W-20 5W-30 10W-30 10W-40 | 20W-30 20W-20 20W-40 25W-30 |
| 20W-30 20W-20 25W-20 25W-30 |
| 20W-30 20W-40 25W-20 25W-30 |
| 5W-30 10W-30 | 20W-30 25W-30 |
| 20W-30 25W-30 |
| 5W-30 | 20W-30 25W-30 |
| 5W-30 5W-40 |
| 20W-40 20W-30 25W-30 25W-40 |
| 20W-40 20W-30 25W-30 25W-40 |
| 20W-40 20W-30 25W-30 25W-40 |
| 5W-40 |
| 0W-30 5W-40 |
| 20W-40 25W-40 |
| 20W-40 25W-40 |
| 0W-40 5W-40 | 20W-40 25W-40 |
VAZ oil change in Vladimir - prices
- 09/10/2019 Evgeniy: Piston 76.7 D(C) for the VAZ 2108 is required based on availability AutoGlobus: Good afternoon, there is a repair size of 76.4 and the next one is 76.8, the size you requested does not exist.
- Auto parts store VAZ spare parts: Good afternoon, the VAZ 2108 does not have 76.7 pistons, only 76.4 and 76.8
- Evgeniy: you didn’t have it, but I found it. Thank you!
- 03/05/2019 Lev: Changing the oil in the automatic transmission Volvo s80 2.5 2010
- Vasya diagnostician: Good evening! 1580 rubles taking into account your materials and adaptation of the automatic transmission after an oil change.
- Leo: The material is oil and that's it? There is no need for a filter. How much oil should I bring?
- Leo: How much does a full replacement cost? And why is it worse or better?
- Vasya diagnostician: Complete replacement only 1500 RUR. With computer diagnostics.
- 09/05/2018 Alexander: Availability and cost of the VAZ -2105 rear axle gearbox or those that are in stock
- AutoGlobus: Gearbox is available, cost 6390 rub.
- Alexander: thank you
- ASPARTA auto parts: Good afternoon! In stock AVTOVAZ – 6000 RUR
Most often, people search for “VAZ oil change,” but there are also other formulations, for example:
Lada oil change
- Lada oil change
The most popular features of the locations found: paintless dent removal, car alarm repair, chrome plating of car parts, wholesale car accessories, buyback of problem cars, Shanghai Maple, Datsun, Aston Martin, Opel, Ultima.
PJSC AvtoVAZ is a Russian automotive company, the largest manufacturer of passenger cars in Russia and Eastern Europe. Control over the company belongs to the Renault-Nissan alliance and Rostec. The full official name is Public Joint Stock Company AvtoVAZ.
When to change the oil
When it’s time to change the oil in a VAZ 2105 engine, you must follow the manufacturer’s instructions. So:
- If the car is new, then you can follow the manufacturer's recommendations.
- If the car has significant mileage, then you need to learn how to determine these terms yourself.
- In a new car, the manufacturer recommends changing the oil after 15,000 km. But if the car is no longer new, then this period should be reduced to 10,000 km or even 7,500 km.
Attention: In any case, when measuring the oil level in the crankcase, pay attention to the transparency of the oil and its viscosity. If the oil has darkened or even turned black, and the viscosity is no longer the same to the touch, then it is better to change the oil ahead of time.
The timing of an oil change is greatly influenced by the condition of the piston rings, the quality of the gasoline you drive and the quality of the oil itself. If you have to change the oil on a VAZ 2105 engine, follow the instructions below.
VAZ 2105 oil change yourself How is it?
- 1 Frequency of engine and gearbox oil changes 1.1 Which oil to choose for the VAZ 2105 engine and gearbox?
- 3.1 Vehicle preparation
In technology without lubrication, little moves as it should. Therefore, it is important that there is oil in the engine, gearbox, and rear axle, but this same oil loses its properties over time and needs to be changed. These instructions for changing the oil on a VAZ 2105 car will tell you in detail about when to change the oil, in what sequence and how. Also here you will find useful tips and photos and videos that clearly show the essence of the process.
- Frequency of engine and gearbox oil changes
- Which oil to choose for the VAZ 2105 engine and gearbox?
- Oil change tools
- Change of oil
- Preparing the car
- Changing engine oil VAZ 2105
- Changing the oil in the VAZ 2105 gearbox
- Changing the oil in the rear axle
Stages of changing the oil in a VAZ 2107 injector engine
To change the engine oil on a VAZ 2107, you will need a torque wrench and a spark plug. The process of changing the oil fluid is the same for both injection and carburetor engines.
Step-by-step instructions for draining the oil:
- Warm up the power unit. Drive the car onto a viewing hole or overpass. Is there neither one nor the other? You can use a jack to raise the car after securing the vehicle with the handbrake.
- Open the hood. Unscrew the filler cap. Place a container with a volume of at least five liters in the lower part under the drain hole.
- Unscrew the drain plug with a 12 mm hexagon.
- Wait 10-15 minutes until the oil has completely drained from the system.
- Tighten the plug. If necessary, change the rubber ring of the plug.
When changing the type of oil or every 30 thousand kilometers, the power unit is flushed. To carry out this procedure, you will need a special additive. Motor oil is forced through the entire system. More details below.
Step-by-step instructions for flushing the power unit on a VAZ 2107:
- Pour flushing fluid into the power unit. Let the car idle for about 10 minutes.
- Unscrew the oil filter using a screwdriver. Pour about 200 ml of fresh oil into the new filter housing and screw it back in.
- Replace the drain plug. Please note: Some drain plugs do not have a gasket. They are conical in shape.
- Pour 3.5 liters of oil liquid through the filler neck. Use a funnel. After filling, make sure there are no leaks. Carefully inspect the drain plug.
- Start the engine. Observe the light on the instrument panel. It should go out immediately after starting the engine.
- Let the engine run for 3-5 minutes. Turn off the engine and let stand for 10-15 minutes. Check the oil level again with the dipstick. If necessary, top up.
Features of changing oil in the VAZ 2107 engine injector and carburetor
Changing the oil in a VAZ 2107 engine is no different, regardless of whether it is an injector or a carburetor.
Changing the oil and oil filter VAZ “classic”
So, let's look at the oil change procedure using the VAZ 2106 as an example. First of all, the volume of oil in the VAZ 2106 engine for replacement is 3.75 liters. You also need to purchase a new oil filter that will be completely suitable for this type of engine.
- First of all, before changing the lubricant, the engine must be warmed up to operating temperatures. This will maximize the fluidity of the oil, which liquefies with heat. End of form
- Then the car needs to be lifted on a lift and driven onto an overpass or inspection hole. The main task is to gain free access to the drain hole, which is made in the oil pan.
- Next (in the case of an inspection hole or overpass), the car is fixed using the handbrake and engaging first gear. You can also additionally install wheel chocks, etc.
- If there is an installed engine crankcase protection, it is recommended to remove such protection, even taking into account the fact that a special hole may be made in the protection itself for draining the oil. This will make the procedure easier if you lack practical skills in changing the oil.
Now let's move on to the necessary tools. For example, on the popular VAZ “six” you will need:
- Allen key for 12 or cue ball with a wrench;
- Container for draining waste from the engine (volume 5 l.)
- Puller key for removing the oil filter;
- Funnel for pouring fresh oil;
- Rags, protective gloves, brush with metal bristles;
If the car has a crankcase protection, other keys may be required for dismantling (depending on the mounting features of the protection itself). After the engine has warmed up, the engine should be turned off. Then the protection is removed (if any). It is better to carry out all work wearing protective gloves.
Now you can lift the hood and unscrew the oil filler cap. If you plan to flush the engine and use a composition known as “five-minute solution,” then this product is poured directly into the exhaust, and the neck cap is screwed back on.
Next is a quick flush of the engine. When finished, you need to unscrew the neck cap again, go down under the car, placing a container under the place where the drain plug is installed in the pan.
Now the drain plug is cleaned with a brush with metal bristles, after which the drain plug is carefully unscrewed with a hex key. At the same time, if necessary, place a pre-prepared container to drain the oil.
Gradually and as the lubricant flows out, the plug is completely unscrewed. Next, the oil will flow out of the drain hole for about 15 minutes. This time is enough to wipe the drain plug with a clean rag.
When the oil stops dripping, the drain plug is screwed back in. If it is necessary to flush the engine before changing the oil using full-volume flushing fluids, then flushing oil is poured in, the oil filler cap is screwed back on and the internal combustion engine is flushed according to the instructions indicated on the package.
Having completed flushing the engine oil system, the procedure for changing the oil itself can be continued. The flushing is drained from the engine in the manner described above, the drain plug is screwed in.
How to replace a VAZ oil filter
Now, that is, immediately before adding fresh oil, you can proceed to replacing the oil filter. By the way, in some cases, especially if you need to wash the engine with full-volume flushing oil, it is recommended to replace the filter twice.
This means you must first remove the old one before washing, install a clean one (the cheapest one will do), then perform the washing itself. After washing, you will need to remove the recently installed cheap filter again and install a high-quality new one.
- Let's get back to the withdrawal. The oil filter can be removed quickly and easily using a special wrench puller. However, not everyone has such a key. For this reason, you need to familiarize yourself with how to unscrew the oil filter with a screwdriver or using other methods.
- Now you need to pour a little clean engine oil into the new filter, filling it halfway. This will allow the lubricant to saturate the filter elements in the housing. The rubber o-ring on the oil filter is also lubricated with oil.
Before installation, wipe the area where the filter is installed with a clean cloth, and then tighten the new filter by hand. Next, insert a funnel into the oil filler neck and pour in fresh oil.
Stages of changing the oil in a VAZ 2107 injector engine
To change the engine oil on a VAZ 2107, you will need a torque wrench and a spark plug. The process of changing the oil fluid is the same for both injection and carburetor engines.
Step-by-step instructions for draining the oil:
- Warm up the power unit. Drive the car onto a viewing hole or overpass. Is there neither one nor the other? You can use a jack to raise the car after securing the vehicle with the handbrake.
- Open the hood. Unscrew the filler cap. Place a container with a volume of at least five liters in the lower part under the drain hole.
- Unscrew the drain plug with a 12 mm hexagon.
- Wait 10-15 minutes until the oil has completely drained from the system.
- Tighten the plug. If necessary, change the rubber ring of the plug.
When changing the type of oil or every 30 thousand kilometers, the power unit is flushed. To carry out this procedure, you will need a special additive. Motor oil is forced through the entire system. More details below.
Step-by-step instructions for flushing the power unit on a VAZ 2107:
- Pour flushing fluid into the power unit. Let the car idle for about 10 minutes.
- Unscrew the oil filter using a screwdriver. Pour about 200 ml of fresh oil into the new filter housing and screw it back in.
- Replace the drain plug. Please note: Some drain plugs do not have a gasket. They are conical in shape.
- Pour 3.5 liters of oil liquid through the filler neck. Use a funnel. After filling, make sure there are no leaks. Carefully inspect the drain plug.
- Start the engine. Observe the light on the instrument panel. It should go out immediately after starting the engine.
- Let the engine run for 3-5 minutes. Turn off the engine and let stand for 10-15 minutes. Check the oil level again with the dipstick. If necessary, top up.
How to change engine oil on a VAZ 2101-VAZ 2107?
Draining: 1) First you need to remove the cap from the oil filler neck.
2) Next you will need to unscrew the drain plug.
3) Whatever pollutes the environment, place some container for drained oil.
4) After the oil has poured out of the hole, you will need to screw the plug back on.
5) Now unscrew the oil filter and remove it.
Note! You can unscrew the oil filter by hand, but if nothing comes out, use a special wrench!
Pouring:
If you are going to fill in with a different brand of oil, then you need to: 1. Drain the old oil. (We do not change the oil filter!) 2. Fill in new oil to the bottom mark on the dipstick. 3. Start the car and let it run for about 10 minutes. (You can’t move away!) 4. Turn off the car and drain the oil. 5. Replace the oil filter with a new one. 6. Now you can fill in new engine oil. (You need to fill up to the top mark on the dipstick!)
If you are not going to change the brand of oil, then you need: 1. First, pick up a new oil filter. 2. Then pour new engine oil into it, one-third of the filter volume. (A third of the volume is slightly less than half the filter.) 3. Then lubricate the filter O-ring with new engine oil. 4. Then screw the new filter into place. (Wrap it with your hands!) 5. Now you need to pour clean oil into the oil filler neck (For convenience, you can use a funnel!) 6. After pouring the oil, start the car and let it run for a few minutes. (You should not drive the car right away!) 7. While the engine is running, look to see if oil is leaking from under the drain plug or oil filter.
