Piston pin diameter VAZ 2101

1200 rub. for the photo report

We pay for photo reports on car repairs. Earnings from 10,000 rubles/month.

Write:

The marking of pistons allows us to judge not only their geometric dimensions, but also the material of manufacture, production technology, permissible installation gap, manufacturer's trademark, installation direction and much more. Due to the fact that there are both domestic and imported pistons on sale, car owners sometimes face the problem of deciphering certain designations. This material contains as much information as possible, allowing you to obtain information about the markings on the piston and understand what the numbers, letters and arrows mean.

The picture is interactive. When you hover, information about decryption appears

Information on the piston surface

Discussing the question of what markings on pistons mean, it is worth starting with what information the manufacturer puts on the product.

1. Piston size . In some cases, in the markings on the bottom of the piston you can find numbers indicating its size, expressed in hundredths of a millimeter. Example - 83.93. This information means that the diameter does not exceed the specified value, taking into account the tolerance (tolerance groups will be discussed below; they differ for different brands of cars). Measurement is carried out at a temperature of +20°C.
2. Installation gap . Its other name is temperature (since it can change along with changes in the temperature regime in the engine). Designated as Sp. It is given in fractional numbers, meaning millimeters. For example, the marking on the SP0.03 piston indicates that the gap in this case should be 0.03 mm, taking into account the tolerance range.
3. Trademark . Or an emblem. In this way, manufacturers not only identify themselves, but also provide information to craftsmen about whose documentation (product catalogs) should be used when selecting a new piston.
4. Installation direction . This information answers the question - what does the arrow on the piston point to? It “tells” how the piston should be mounted, in particular, the arrow is drawn in the direction of forward movement of the car. On cars where the engine is located at the rear, instead of an arrow, a symbolic crankshaft with a flywheel is often depicted.
5. Casting number . These are numbers and letters that schematically indicate the geometric dimensions of the piston. Typically, such designations can be found on European machines, for which the piston group elements are manufactured by companies such as MAHLE, Kolbenschm >

In addition to these designations, there are also others, and they may differ from one manufacturer to another.

VAZ pistons marking

According to statistics, owners or engine repair technicians of VAZ cars are most often interested in the marking of repair pistons. Below we provide information on various pistons.

VAZ 2110

For example, let's take the engine of a VAZ-2110 car. Most often, this model uses pistons marked 1004015. The product is produced directly at AvtoVAZ OJSC. Brief technical information:

• nominal piston diameter - 82.0 mm;
• piston diameter after first repair - 82.4 mm;
• piston diameter after the second repair - 82.8 mm;
• piston height - 65.9;
• compression height - 37.9 mm;
• The recommended clearance in the cylinder is 0.025...0.045 mm.

Additional information can be printed directly on the piston body. For example:

• “21” and “10” in the area of ​​the hole for the finger - designation of the product model (other options - “213” indicates the VAZ 21213 engine, and for example, “23” - VAZ 2123);
• “VAZ” on the inside of the skirt is the manufacturer’s designation;
• letters and numbers on the inside of the skirt are a specific designation of foundry equipment (you can decipher it using the manufacturer’s documentation, but in most cases this information is useless);
• “AL34” on the inner side of the skirt is the designation of the cast alloy.

The main marking symbols applied to the piston crown:

• The arrow is an orientation marker indicating the direction towards the camshaft drive. On the so-called “classic” VAZ models, sometimes instead of an arrow you can see the letter “P”, which means “in front”. Likewise, the edge where the letter is depicted should be directed towards the direction of movement of the car.
• One of the following symbols is A, B, C, D, E. These are diameter class markers that show the deviation in the outside diameter value. Below is a table with specific values.
• Piston mass group markers. “G” is normal weight, “+” is weight increased by 5 grams, “-” is weight decreased by 5 grams.
• One of the numbers is 1, 2, 3. This is a piston pin hole class marker that determines the deviation in the diameter of the piston pin hole. In addition to this, there is a color designation for this parameter. So, the paint is applied to the inside of the bottom. Blue color - 1st grade, green - 2nd grade, red - 3rd grade. The following provides additional information.

For VAZ repair pistons there are also two separate designations:

• triangle - first repair (diameter increased by 0.4 mm from the nominal size);
• square - second repair (diameter increased by 0.8 mm from the nominal size).

Please note that for different brands of cars (including for different engines), the difference between repair pistons should be found in the reference information.

VAZ 21083

Another popular VAZ piston is 21083-1004015. It is also produced at OJSC AvtoVAZ. Its technical dimensions and parameters:

• nominal diameter - 82 mm;
• diameter after first repair - 82.4 mm;
• diameter after the second repair - 82.8 mm;
• piston pin diameter - 22 mm.

Dimensions and markings of piston rings VAZ 2109 – 2115

I will now give you the main dimensions of the connecting rod and piston group below in the figure.

The piston is cast aluminum. According to the outer diameter, the pistons are divided into five classes (A, B, C, D, E) every 0.01 mm. The outer surface of the piston has a complex shape. Therefore, it is necessary to measure the piston diameter only in a plane perpendicular to the piston pin, at a distance of 55 mm from the piston bottom.

Main dimensions of the connecting rod VAZ 2109 – 2115

Based on the diameter of the hole for the piston pin, pistons are divided into three classes (1, 2, 3) every 0.004 mm.

The classes of piston diameters and holes for the piston pin are stamped on the bottom of the piston (Fig. 4).

The piston is cast aluminum. According to the outer diameter, the pistons are divided into five classes (A, B, C, D, E) every 0.01 mm. The outer surface of the piston has a complex shape. Therefore, it is necessary to measure the piston diameter only in a plane perpendicular to the piston pin, at a distance of 55 mm from the piston bottom.

Dimensions of piston rings VAZ 2109 – 2115

Based on the diameter of the hole for the piston pin, pistons are divided into three classes (1, 2, 3) every 0.004 mm.

The classes of piston diameters and piston pin holes are stamped on the piston crown.

Piston markings VAZ 2109 – 2115

Marking of ZMZ pistons

Another category of car owners interested in piston markings have ZMZ brand motors at their disposal. They are installed on GAZ cars - Volga, Gazelle, Sobol and others. Let's look at the symbols on their bodies.

The designation “406” means that the piston is intended for installation in the ZMZ-406 engine. There are two markings stamped on the piston crown. According to the letter painted on the new block, the piston is matched to the cylinder. When repairing with cylinder boring, the required clearances are made during the process of boring and honing for pre-purchased pistons with the required size.

The Roman numeral on the piston indicates the correct piston pin group. The diameters of the holes in the piston bosses, the connecting rod head, as well as the outer diameters of the piston pin are divided into four groups, marked with paint: I - white, II - green, III - yellow, IV - red. On the fingers, the group number is also marked with paint on the inner surface or on the ends. It must match the group indicated on the piston.

The group number should similarly be marked with paint directly on the connecting rod. In this case, the mentioned number must either coincide or be next to the number of the finger group. This selection ensures a situation where the lubricated pin moves with little effort in the connecting rod head, but does not fall out of it. Unlike VAZ pistons, where the direction is indicated by an arrow, on ZMZ pistons the manufacturer directly writes the word “FRONT” or simply puts the letter “P”. During assembly, the protrusion on the lower head of the connecting rod must coincide with this inscription (be on the same side).

There are five groups, with a pitch of 0.012 mm, which are designated by the letters A, B, C, D, D. These size groups are selected according to the outer diameter of the skirt. They correspond to:

• A - 91.988...92.000 mm;
• B - 92,000...92,012 mm;
• B - 92.012...92.024 mm;
• G - 92.024...92.036 mm;
• D - 92.036...92.048 mm.

The value of the piston group is stamped on its bottom. So, there are four size groups, which are marked with paint on the piston bosses:

• 1 - white (22.0000...21.9975 mm);
• 2 - green (21.9975...21.9950 mm);
• 3 - yellow (21.9950...21.9925 mm);
• 4 - red (21.9925...21.9900 mm).

Pin hole group marks can also be applied to the piston bottom in Roman numerals, with each digit corresponding to its own color (I - white, II - green, III - yellow, IV - red). The size groups of the selected pistons and piston pins must match.

The ZMZ-405 engine is installed on the GAZ-3302 “Gazelle Business” and GAZ-2752 “Sobol” vehicles. The calculated gap between the piston skirt and the cylinder (for new parts) should be 0.024...0.048 mm. It is defined as the difference between the minimum cylinder diameter and the maximum piston skirt diameter. There are five groups, with a pitch of 0.012 mm, which are designated by the letters A, B, C, D, D. These size groups are selected according to the outer diameter of the skirt. They correspond to:

• A - 95.488...95.500 mm;
• B - 95.500...95.512 mm;
• B - 95.512...95.524 mm;
• G - 95.524...95.536 mm;
• D - 95.536...95.548 mm.

The value of the piston group is stamped on its bottom. So, there are four size groups, which are marked with paint on the piston bosses:

• 1 - white (22.0000...21.9975 mm);
• 2 - green (21.9975...21.9950 mm);
• 3 - yellow (21.9950...21.9925 mm);
• 4 - red (21.9925...21.9900 mm).

Thus, if, for example, the letter B is written on the piston of a GAZ engine, this means that the engine has been overhauled twice.

In ZMZ 409, almost all dimensions are the same as in ZMZ 405, with the exception of the recess (puddle), it is deeper than in 405. This is done to compensate for the compression ratio, the size h increases on the pistons 409. Also, the compression height of 409 is 34 mm, and for 405 it is 38mm.

We provide similar information for the ZMZ 402 engine.

• A - 91.988...92.000 mm;
• B - 92,000...92,012 mm;
• B - 92.012...92.024 mm;
• G - 92.024...92.036 mm;
• D - 92.036...92.048 mm.

“Selective selection” inscription on pistons

• 1 - white; 25.0000…24.9975 mm;
• 2 - green; 24.9975…24.9950 mm;
• 3 - yellow; 24.9950…24.9925 mm;
• 4 - red; 24.9925…24.9900 mm.

Please note that since October 2005, on pistons 53, 523, 524 (installed on many models of ZMZ engines, among others), the “Selective Selection” seal is installed on their bottom. Such pistons are manufactured using more advanced technology, which is described separately in the technical documentation for them.

Replacing piston rings

On VAZ cars, as well as on all other models of passenger cars, it is advisable to change only the piston rings only if:

1. there is no exhaust in the cylinders;
2. there are no signs of damage to their inner surface.

If the liners are significantly worn, they need to be bored, and if the last size was already used before, the cylinder block needs to be relined. You can replace the PC on any VAZ engine without removing the internal combustion engine; this will require removing the cylinder head and oil sump. PCs are replaced if the gap at the joints does not exceed 1 mm.

For example, let's consider replacing piston rings on a VAZ-2114 car with an 8-valve internal combustion engine; such work must be carried out on a pit or a car lift:

• turn off the ignition, put the gearbox in neutral, disconnect the negative terminal from the battery;
• drain the antifreeze, remove the air filter housing along with the pipe (injector corrugation);
• remove the valve cover, camshaft, loosen the timing belt and move it to the side;
• disconnect the wires and cooling system pipes from the cylinder head, unscrew the head bolts;
• unscrew the nuts of the exhaust pipe of the muffler;
• We completely free the cylinder head from all fasteners that prevent it from being removed, and we remove the cylinder head;

• if there is protection under the engine, remove it;
• place a container under the engine sump, unscrew the plug on the crankcase, drain the oil;
• remove the lower hatch of the gearbox housing (three bolts);
• Using a 10 mm wrench or a socket wrench, unscrew all the oil pan bolts;

• dismantle the pan, remove the oil receiver;

• Unscrew the connecting rod nuts, remove the lower connecting rod caps, and carefully knock the pistons and connecting rods upward. Pistons should be knocked out through a soft metal drift or through a wooden block. First, you need to carefully knock out the connecting rod bolt without damaging the threads on it, then place the drift on the end of the connecting rod - in no case should you hit the bearings or the seat underneath them;

• It is recommended to remove the connecting rods one at a time, and immediately attach the caps to them; the caps should not be confused with each other, they are placed back strictly in their places, and a lock to the lock is required;
• remove the PC from the pistons, use a piece of the old ring to clean the piston grooves to bare metal. Be sure to check the cleanliness of the groove all around; there should be no coke left in it;

• We install new rings in the grooves, start with the lower MPC, then install the middle compression PK, and lastly the upper one. For installation, you can use a special device, but it is still more convenient to install the rings by hand. If the MPCs are cast iron, they cannot be bent along their axis, they can only be carefully moved apart. Compression rings also need to be bent carefully, to a minimum;
• we install the piston in place using a special mandrel, hammer it in with a wooden hammer handle or a brass or bronze drift;

Toyota pistons markings

The pistons on Toyota engines also have their own designations and sizes. For example, on the popular Land Cruiser, the pistons are designated by the English letters A, B and C, as well as numbers from 1 to 3. Accordingly, the letters indicate the size of the hole for the piston pin, and the numbers indicate the size of the piston diameter in the “skirt” area. The repair piston has +0.5 mm compared to the standard diameter. That is, only the letter designations change for repair shops.

Please note that when purchasing a used piston, it is necessary to measure the thermal gap between the piston skirt and the cylinder wall. It should be within 0.04...0.06 mm. Otherwise, it is necessary to carry out additional diagnostics of the engine and, if necessary, carry out repairs.