How to change the oil in a Toyota Auris engine yourself? Volume of coolant, engine oil, manual and automatic transmission oils Toyota Auris How much oil is in the Toyota Auris 1.6 engine

Engine oil Toyota Auris, 1st generation (E150), 2007 - 2012

1.3 l, 101 hp, gasoline, front-wheel drive, manual transmission, 2009 - 2012

• Trims: 1.33 MT Elegance, 1.3 MT Comfort
• Engine: 1NR-FE

1.4 l, 97 hp, gasoline, manual transmission, front-wheel drive, 2007 - 2009

• Options: 1.4 MT Elegance
• Engine: 4ZZ-FE

1.6 l, 124 hp, gasoline, manual transmission, front-wheel drive, 2010 - 2012

• Trim: 1.6 MT Comfort+
• Engine: 1ZR-FAE

1.6 l, 124 hp, gasoline, front-wheel drive, manual transmission/robot/automatic transmission, 2007 - 2012

• Trims: 1.6 MT Prestige, 1.6 MultiMode Prestige, 1.6 AT Comfort+, 1.6 AT Prestige, 1.6 AT Elegance
• Engine: 1ZR-FE

1.6 l, 132 hp, gasoline, front-wheel drive, manual transmission/robot, 2009 - 2012

• Trims: 1.6 MT Elegance Plus, 1.6 MultiMode Prestige, 1.6 MultiMode Elegance Plus
• Engine: 1ZR-FAE

1.8 l, 147 hp, gasoline, manual transmission, front-wheel drive, 2009 - 2010

• Equipment: 1.8 MT Elegance Plus
• Engine: 2ZR-FAE

* — service oil volume is indicated.
** - when operating a vehicle in difficult conditions (high load, harsh environmental conditions, low quality fuel, city traffic jams and short trips), it is recommended to reduce the engine oil change interval by 2 times.

Found an error in your data? Please let us know about it.

Oil change Toyota Auris

102 1 79k

130 9 124k

Calculator for calculating oil change intervals based on fuel consumption

How to calculate oil change intervals based on actual fuel consumption

This video shows how to change the engine oil, replace the oil filter and change the oil in the box (robot) of a 2009 Toyota Auris with a 1.6 engine. In principle, you can change the oil yourself, but there are a couple of nuances.

How to change Toyota Auris oil

The car is installed on a pit or overpass. Next, you need to place a container under the drain hole, unscrew the drain plug and drain the old oil. Then screw the plug back, changing the washer on it if necessary.

The engine oil filter is unscrewed using a special puller, and a little oil will also leak out . After unscrewing the oil filter cap, you should change the filter element and rubber seals, and then put everything back. Since the box here is robotic, there is no filter on it.

Therefore, all that remains is to fill in new oil. The engine filler neck is located under the hood, and to fill the Toyota Auris box with oil, you need to unscrew the plug ( 24mm wrench) , which is located approximately under the left front wheel.

When to change Toyota Auris oil

The repair manual requires changing Toyota Auris engine oil every 10,000 km, along with the oil filter. In difficult operating conditions (in a big city and dusty areas), this interval is reduced to 7-8 thousand km. The frequency of oil changes in the box is 40,000, with a level check every 10,000.

How much oil in Toyota Auris and what kind of oil to fill

To replace the 4ZZ-FE and 1ZR-FE Toyota Auris engines, you will need approximately 4.2 liters of synthetic oil, and for the 1NR-FE engine - 3.4 liters. According to the manual, the viscosity should be filled with 0W30 oil or 5W40 oil, class A3, B3, B4 - according to ACEA; SI/CF - via API.

The box will contain approximately 1.9 liters of API GL-4, SAE 75W90 semi-synthetic gear oil.

How often to change oil in Toyota Auris

For the Toyota Auris power plant, a mileage of 10,000 km is considered optimal. However, under severe operating conditions, the service interval must be reduced to 8000-9000 km.

In the case of gearboxes, automatic transmissions are serviced at least once every 40,000 km, and automatic transmissions - 60,000 km. At the same time, the actual volume of lubricant is checked after each engine maintenance.

Also inside the service documentation it is stated that a complete replacement of the lubricant should be carried out after each repair or if extraneous sounds or structural defects are detected.

The answer to the question of what oil to fill in Toyota Auris can also be found on the manufacturer’s official website. To do this, you need to fill out a form indicating the year of manufacture, engine number and VIN code located on the body or technical passport of the vehicle.

How much oil is in a Toyota Auris engine?

Toyota Auris is a compact five-door hatchback that has been on the market since 2007. The first generation of Auris in terms of design did not differ from the original Coroll sedan of that time, but had significant differences in a more sporty design. The car was delivered to Russia with 1.4 (97 hp) and 1.6 liter (124 hp) gasoline engines. In 2009, an option with a top-end 1.8-liter engine with 147 horsepower appeared, and in 2010 an updated modification of the Toyota Auris was released. Since then, the basic equipment has been equipped with a new 1.3-liter engine (instead of the 1.4-liter). In 2012, sales of the second generation Toyota Auris began. The car was sold in Russia with 1.3 and 1.6 liter engines. Sales completed in 2021.

• 1 Regulations for changing the oil in the internal combustion engine
• 2 Recommended oil
• 3 How much engine oil is needed for Toyota Auris 3.1 Generation 1 (2007-2012)
• 3.2 Generation 2 (since 2012)

The best motor oil. does it exist?

Regulations for changing oil in internal combustion engines

Experienced motorists and experts recommend changing the oil in the Toyota Auris engine every 10-15 thousand km. If you use old motor oil for a long time, you will have to face serious problems, including major repairs, which will be preceded by various problems:

• If the useful properties of the oil have expired and are not changed for a long time, then the load on engine parts increases, and the effect of dry friction occurs between rubbing parts that lack high-quality lubrication.
• Possible engine knocking, overheating or excessive fuel consumption
• Anti-corrosion protection deteriorates
• Oil does not remove heat well, parts overheat and melt
• Combustion products accumulate in the engine channels, causing the channels to become clogged and the engine to fail.

When is an oil change required?

The oil change schedule for Toyota Auris is 10,000 -12,000 km. Every 12 months, the lubricant should be drained and new fluid should be added. This will ensure optimal engine operation and help prevent a number of malfunctions.

However, in addition to clear deadlines, it is worth paying attention to other signs of the need for replacement:

• the engine hums, knocks, creaks and makes noise;
• power and traction decreased;
• when first started, the engine stalls or reacts poorly;
• The instrument panel displays an error.

Oil change Toyota Auris

The instructions will tell you how to change the oil on your car yourself.

Also, together with this procedure, we will replace the filter. You can cope on your own, without the help of specialists, but of course there are some nuances that you need to know about in advance.

And so, about the oil change procedure:

First, we advise you to warm up the engine. This way the oil will drain much more actively. Next, place the car on the inspection pit, you can use the overpass. Now take a container and place it under the drain hole, unscrew the drain plug, and begin to drain the old oil. Afterwards you can screw the plug back in, don’t forget that we need to replace the washer.

When is an oil change required?

The oil change schedule for Toyota Auris is 10,000 -12,000 km. Every 12 months, the lubricant should be drained and new fluid should be added. This will ensure optimal engine operation and help prevent a number of malfunctions.

However, in addition to clear deadlines, it is worth paying attention to other signs of the need for replacement:

• the engine hums, knocks, creaks and makes noise;

power and traction decreased;

• when first started, the engine stalls or reacts poorly;
• The instrument panel displays an error.

How to change the oil in a Toyota Auris engine yourself?

Motor oil is one of the most important fluids in a car. Its quality, properties and functionality directly affect the operation of the Toyota power unit. In order for the mechanism to operate smoothly, it is necessary to follow the manufacturer’s instructions and change the oil and oil filter within a clearly defined time frame.

When is an oil change required?

The oil change schedule for Toyota Auris is 10,000 -12,000 km. Every 12 months, the lubricant should be drained and new fluid should be added. This will ensure optimal engine operation and help prevent a number of malfunctions.

However, in addition to clear deadlines, it is worth paying attention to other signs of the need for replacement:

• the engine hums, knocks, creaks and makes noise;
• power and traction decreased;
• when first started, the engine stalls or reacts poorly;
• The instrument panel displays an error.

An oil check is required every 6 months. If the car is operated in difficult conditions, in a dusty environment and the absence of roads, then only checking the lubricant can show the condition and level in the engine. In such cases, the lubricant is replaced earlier - every 5-7 thousand kilometers.

What kind of oil should I use?

Manufacturers recommend that when choosing a lubricant, give preference to the original product - Genuine Motor Oil API. This is a synthetic oil that is suitable for all Toyota Auris models.

If we consider mineral and synthetic lubricants for Toyota, then synthetics with a viscosity grade of 5W-30 are better suited here. Available analogues: CASTROL, MOBIL, LIQUI MOLY, Synthoil, MOTUL.

Amount of oil needed:

• 1.4 liter engine 1ND-TV - 4.3 liters of lubricant;
• 1.6 l 1ZR-FE - 4.2 liters;
• 2.0 l 1AD-FTV - 6.3 l.

Stages of changing the oil in a Toyota Auris engine

To carry out work on updating engine oil, a platform or pit is required to place the car at a height and gain access to the pan.

Preparation for work includes selecting working tools, studying safety precautions and choosing a lubricant.

It is important to understand that the lubricant is drained from the engine hot, and therefore you need to think about your protection. It is better to work in overalls or a robe, rubber gloves and a hat so that the hot drain does not get on the skin and cause burns.

• keys for 15 and 17;
• container for waste liquid;
• new filter;
• canister of new oil;
• rags;
• clean cloth napkins;
• funnel.

How to drain the oil?

Changing the oil in a Toyota Auris engine takes place in several stages:

• Warming up the engine lubricant to operating temperature.
• Turn off the engine.
• Unscrew the drain plug and place a 5-liter container.
• Wait 5-10 minutes until the waste liquid drains completely.

Along with draining the old fluid, it is recommended to change the oil filter.

Sequence of actions when installing a new filter:

• Unscrew the filtration using a puller;
• clean the seat with a rag;
• insert a new element.

How to clean the engine?

After checking the filter and installing a new element, many car enthusiasts and mechanics recommend cleaning the engine. This is necessary in order to remove remnants of old lubricant and wash away carbon deposits from the surface of the assembly parts.

Step-by-step instructions for flushing the engine:

• Tighten the drain hole.
• The flushing mixture is poured through the neck of the oil filler plug.
• The engine must be started and allowed to idle for 5 minutes.
• Shut off the unit and drain the flushing through the drain hole.

Many are not supporters of engine flushing, arguing that a large amount of the mixture remains in the engine components and valves. Before adding new lubricant, you will need to wash out the flushing fluid with mineral oil.

How to fill in new oil?

To fill in new lubricant, you must adhere to the following procedure:

• Tighten the drain hole after flushing.
• Slowly pour new lubricant through the neck.
• The volume of lubricant in Toyota Auris is 4-4.5 liters (for gasoline engines).
• After all the product has been poured in, it is necessary to warm up the engine.
• After 5 minutes, you need to turn off the car and check the oil level and pressure.
• If necessary, add lubricant.

At this point, changing the oil in the Toyota Auris engine with your own hands is completed.

Replacement frequency

Factors influencing the frequency of lubricant replacement:

• intensive driving;
• duration of use of the old lubricant;
• driving on field, dirt, sandy roads and mountainous areas;
• the permissible mileage has been significantly exceeded;
• technical condition of the engine;
• seasonality;
• poor quality lubricant.

By filling in new engine oil in a timely manner, you can avoid a number of malfunctions and major repairs of the Toyota engine.

Changing the engine oil and oil filter Toyota Yaris II 2005 - 2012

Tools:

• Straight box spanner 14 mm
• Wire brush
• Large flat screwdriver
• Oil filter puller "chain"

Parts and consumables:

• Rags
• A container of at least 5 liters for drained engine oil
• Funnel (if needed)
• Fabric gloves
• Synthetic motor oil Toyota “ENGINE OIL 5W-30” - 08880-80845
• O-ring for Toyota engine oil pan drain plug - 90430-12031

• Toyota engine oil filter - 90915-10003

Notes:

The manufacturer recommends replacing the oil and oil filter of the Toyota Yaris 2 after approximately 7–10 thousand kilometers. But when operating the vehicle in severe conditions, change the engine oil twice as often.

When changing engine oil, it is also recommended to replace the Toyota Yaris 2 oil filter at the same time.

Fill with oil of the same brand as the oil that was in the engine.

Drain the oil after driving while the engine is still warm and the oil is at its most fluid. If the engine is cold, start it and warm it up to operating temperature.

1. Place the car on an overpass or inspection hole. Open the hood and lock it in the raised position.

2. Turn counterclockwise and unscrew the engine oil filler cap to allow free air flow while draining used oil.

3. Clean the drain plug in the engine oil pan with a wire brush and then with a rag.

Drain plug in the oil pan

4. Use a key to “14” to loosen the drain plug. Check if the Toyota Yaris 2 drain plug gasket is stuck to the pan. If yes, remove it from the pan after draining the oil.

5. Place a container under the drain hole into which the old oil will be drained. Then finally unscrew the drain plug and wait 10-15 minutes until it all drains.

Warning:

Heated oil can burn your fingers, so the plug should be unscrewed carefully.

The plug must be cleaned of dirt and old oil, then be sure to put on a new O-ring (otherwise oil will seep through the gap formed between the pan and the plug).

6. When the oil stops dripping, screw the drain plug and new gasket back on.

What kind of oil should I put into the Toyota Auris (Yaris) engine?

Toyota Auris (Yaris) oil is selected taking into account the operating conditions of the vehicle and the condition of the engine. Next, we’ll tell you what the manufacturer recommends pouring, and what the car owners chose.

A front-wheel drive car in a hatchback body has been produced since 2007 on the platform of another car of the concern - Toyota Corolla. In 2021, Toyota decided to stop production of the model. In total, two generations of the model were developed and produced - E150 and E180. The car was delivered to Russia with small gasoline engines with a displacement of 1.3 - 1.6 liters.

Toyota Auris: selection and oil change

Any car, regardless of manufacturer, requires timely maintenance. It includes work on changing the engine oil, gearbox, replacing fuel and cabin filters. If this work is carried out on time, then most problems with breakdowns of components and assemblies can be avoided. Below we will try to figure out how to carry out the necessary work on a Toyota Auris.

Changing the oil in a Toyota Auris engine

Toyota Auris is a car that, like any other vehicle, requires timely oil changes and appropriate filters (every 10 thousand km). Let's look at how this process happens below.

In addition, you need to remember the need to replace the antifreeze in this car. In Toyota Auris, replacing antifreeze for the cooling system is a procedure that allows you to avoid various types of problems. According to the manufacturer's recommendations, it must be carried out for the first time - after 160 km, subsequent procedures must be carried out every 80 thousand km.

Antifreeze is allowed to be changed ahead of schedule, if it becomes dirty, the radiator is replaced, or the internal combustion engine is repaired.

Refueling volumes

How much oil is in a Toyota Auris engine? How much will be needed for the procedure?

Toyota Auris oil changes are performed in quantities depending on the engine modification:

1. 1ND-TV 1.4 liter requires 4.3 liters of oil;
2. for 1ZR-FE 1.6-liter, 4.2 liters of oil are required;
3. for 1AD-FTV 2.0 l, 6.3 l of oil should be used;

Oil selection

The oil is selected according to its viscosity level, paying attention to the climatic characteristics of the region of permanent residence. Typically 5W-30 oil is used.

As a rule, drivers prefer to use oils from the following companies:

1. Mobil;
2. Castrol;
3. Liqui Moly Synthoil Longtime.

For Toyota, the original oil is SN/GF-5 0W20 and is synthetic. It is allowed to replace it with SAE 5W-30. The amount of oil required for the engine is determined by the volume of the latter; you can also focus on the volume of the liquid that was drained. For engines with a volume of 1.6, 1.8 liters, about 4 liters of oil are required.

Algorithm of actions

Let's look at a step-by-step oil change for Toyota Auris:

1. warm up the internal combustion engine for 5 minutes (hot oil will flow out of the engine more actively and will not remain inside, which will avoid the situation of mixing old and new substances, which will reduce the characteristics of the product);
2. remove the engine crankcase protection (it is better to carry out these manipulations in the inspection hole);
3. unscrew the filler cap, remove the dipstick, this will create a through hole that will facilitate the rapid flow of liquid;
4. place a container for used oil that can hold 5 liters of used oil;
5. unscrew the plug with a wrench (usually a ratchet is used), working very carefully, because the oil will be hot;
6. when the dirty oil is completely drained, you need to move the basin to the side;
7. now you need to flush the engine with a special liquid, pour it into the engine (you must first close the drain hole with a plug), and let the car run for 5 minutes, then turn off the car and drain this liquid;
8. change the fuel filter, after pouring a little oil into it to lubricate the o-ring;
9. pour new oil, but first check how well the plug is tightened;
10. control the volume of infused liquid using the dipstick, paying attention to the manufacturer’s recommendations (the level on the dipstick should be approximately halfway between its maximum and minimum marks);
11. Check the oil level again after starting the engine and idling.